OUTDOOR CPE (MODEL: TWI 1040–PE)
Telenet’s TWI series of 802.11b/g/n compliant 2.4GHz Wireless LAN products feature 1x1 and 1x2 MIMO antennas. These come in various form factors – For Outdoor applications as a CPE, for outdoor application as an AP, for an indoor AP/Router. It can operate in Point-to-Point and Point-to-Multi-Point links. It can be configured in WDS mode as well.
It can be available with Wireless WAN and Wireless LAN capabilities as well. The TWI series has a high performance radio output and advanced networking and management capabilities. It can support NAT Routing, DHCP server, DHCP relay, DHCP with option 60, QoS, Security based on WPA2/WPA/WEP, Rate Limiting, Broadcast Storm control, etc.
For different applications suitable antennas are provided with appropriate gains. It could have a single antenna for a 1x1, to a multipolarized antenna, and a MIMO antenna for 1x2.
The housing are built according to the applications, such as indoor housing and outdoor housing with ruggedized weatherproof design to meet various IP classes of protection.
GENERAL
General Standard
IEEE 802.11b/g/n WLAN, IEEE 802.3/802.3u Ethernet
Ethernet Interface
Four auto MDX, auto sensing 10/100 Mbps, RJ45 port
Operation modes
Station/Station + WDS
Flash / SDRAM
4 or 8 MB/16 MB
NETWORKING
Networking
DHCP client, Configurable DHCP option 60
Test
PING function and Trace Route function
VLAN
VLAN Support; Management VLAN
ROUTER FEATURE
Networking
NAT, DHCP Client/Server, DNS Proxy
VPN
PPTP/L2TP/IPSec pass-through Pass through
RADIO
Number of Radio
One 802.11 b/g/n Radio
Frequency Range
2400 - 2490Mhz
Channel Bandwidth
Narrow Bandwidth 20 / 40 MHz Support ; Auto in STA mode
RF transmission power
20Dbm
Receiver Sensitivity
-94 dBm
ANTENNA
Internal Antenna gain
8dBi
Internal Antenna3 dB Beamwidth
65 Degrees / 65 Degrees
Internal Antenna Polarization
Horizontal Polarization
MANAGEMENT
NMS
Can be Integrated with Centralised Web Based Management
System for Monitoring,Configuration and Software Upgrade
Management – Device
HTTP Web-based GUI, Telnet Management, button for factory
reset,
Firmware Upgrade
Automated centralised Firmware Upgrade &WebGUI manual
upgrade ; Keep setting when Firmware Upgrade
LED indication
Power, Ethernet , Wireless signal strength
ETHERNET INTERFACE -SPECIFICATION
Ethernet Connectors
RJ-45 Jacks, 4 Ports 10/100 Base-TX with Auto-MDIX
4-Ports PoE (Data+Power IN)
Standards
IEEE Std.802.2 10BASE-T 10Mbps,Half/Full Duplex;
IEEE Std.802.23u 100BASE-TX,10/100Mbps, Half/Full
Duplex;IEEE Std.802.3x Flow control and Back-pressure.
Surge Protection
Protection against initial ESD/EFT Transient Suppression
Technology
Store & Forward switching architecture
Network Cable
2-Pair UTP/STP Cat 5 24AWG Cable
LED’s
Link/Activity per Ethernet Port
Power Over Ethernet Injector: Power
Supply(IN) for CPE.
Power over Ethernet 12V, 1A (12 Watts) on Spare pair to
supply power to the CPE
No. of Ethernet Ports that can Power ON
the CPE.
Anyone/All of the four LAN ports
Max Packet size supported
1536 bytes
Port Isolation
Using Port-based VLAN
Support Broadcast Storm control per
port
Yes
SECURITY
Wireless Security
WEP, WPA2 - PSK(TKIP/AES)
WPA2-AES with 802.1x
802.1x Supplicant EAP-TTLS
MSCHAPV2, EAP-TTLS support
POWER
Power options
100-270 V 50/60 Hz, Indian PIN type
Powering through POE DC power
Power Method
Passive Power over Ethernet
Max Power Consumption
4 Watts
Power Supply
12V, 1A (12 Watts). Power Supply and POE injector included
PHYSICAL
Physical Dimension/ Form factor
Compact and easily mountable on house window
Enclosure Size
175 x 168 x 52 mm
Operating temperature
(0 to 50 deg cent) Outdoor Temprature
Humidity
5 to 90% Condensing
ENVIRONMENT PROTECTION
Compliances
WEEE,RoHS
Shock and Vibration
ETSI300-0110-1.4
Protection
Dust Protected , Protected from Spray Water upto 60 Degree
from V
Enclosure Characteristics
Outdoor UV Stabilized Plastic
